HOLES AND TEARS IN OXFORDS
Tiny holes can appear at random throughout an oxford shirt due to the weaving process. These should not be confused with damage from bleach. Oxford consists of two, thin warp yarns to every soft, thicker yarn in the filling direction. The unbalanced construction causes the thin yarns to break, leaving tiny holes. Manufacturers could use a higher twist in the yarn to retard the development of holes, but eventually any oxford weave will develop tiny pinholes.
In addition, tears in oxfords occur in the direction of the softly twisted, thicker yarns. All the yarns in an oxford receive the same care process, but the constant abrasion in the wear causes the thin yarns to weaken and tear.
Most dress shirts are difficult to shrink. The manufacturer has already allowed for the normal two percent and progressive shrinkage requirements. This shrinkage is usually not enough to cause a complaint. Shrinkage beyond this is usually due to poorly stabilized materials.
Shrinkage complaints can easily be resolved by measuring the collar and sleeve length. Measure the collar from the end of the buttonhole to the center of the button. Measure the sleeve length in a straight line from the center of the back of the collar at the seam to the end of the cuff. If these measurements correspond to the shirt size, it has not shrunk.
WEAR LIFE EXPECTANCY
Determining how long a shirt should last is difficult due to the variances in frequency of wear. However, industry experience shows that, on average, shirts have a two year wear life expectancy. The number of launderings is a better measuring method. The average shirt should have a wear life of 35 to 50 washings. This will fluctuate depending on the amount of abrasion and strain placed on the shirt during wear, the fiber content, the type of fabric, and the laundering procedure.
PERSPIRATION AND ANTIPERSPIRANT DAMAGE
Perspiration, if allowed to stay in a shirt, will eventually stain and also weaken the fabric, allowing the weakened area to be removed during washing. Aluminum chlorides founding antiperspirants will also weaken the fibers under the arm. Controlled use of antiperspirants and frequent washing immediately after wear may minimize this type of damage.
What causes puckering and excess fabric in the shirt collar after laundering?
This is caused by shrinkage of the interfacing (Whiting the collar). If the shirt is laundered and the interfacing shrinks excessively, it will cause the puckering of the outer fabric. The manufacturer must select an interfacing which is compatible with the shirt fabric.
What causes the collar and cuff to have a mottled gray or shiny look in specific areas?
This occurs when excess adhesive is used to fuse the collar or cuff fabric and the interfacing. This excess adhesive softens in pressing and penetrates the outer fabric of the collar and cuffs. This can be prevented by the correct selection of an adhesive that is compatible to commercial laundering.
Why does yellowing occur?
Because some interfacings on shirts react adversely with chlorine, laundries often use other oxygen-type bleaches which do not react with chlorine retentive resins. If chlorine bleach is used on this type of fabric, yellowing could occur.
Buttons may crack during pressing even though the press padding is in excellent conditions and the procedures used are correct. The reason for this is that there is an inherent problem in the button or the way the button was applied to the shirt. The majority of shirt buttons are made from a polyester resin. The strength of the button depends on the amount of polyester in the resin; some imported buttons contain less polyester.
Off-quality buttons are graded because they do not meet the requirements in one or all of the following criteria: color, visual inclusions, chips or cracks, and uniformity of size. Some manufacturers use less expensive, off-quality buttons to same money, but this sometimes results in higher than average breakage.
The Care Label Rule states that the color in a garment must withstand the recommended care procedure. If the dyes in a multicolored shirt are not colorfast to water, bleeding will occur. The dye will migrate into adjacent areas during the washing process. this migration of the dye into surrounding areas is not acceptable unless the fabric is a madras (plaid or stripe that is guaranteed to bleed).
Some dyes dissolve in water and are partially removed during laundering. After the first laundering, the lightening of color may be apparent, or it may be progressive and only noticeable after several care procedures.
Household products like medicinal agents, strong acids, the acid residue of some food-stuffs and beverages, or liquid chlorine bleach can easily damage a shirt. Spillage of a strong household product causes localized fabric weakness or color loss in the area of contact with the fabric. This type of damage may not show up until after washing. This type of staining is not unique to shirts.
HOLES AND TEARS IN OXFORDS